Application of gray-based Taguchi method in optimal analysis of effect of surface micro-texture on friction and wear performance of sliper-swash plate pairs in axial piston pumps
- Authors: Loi Van Le 1, Ping Xu 1, Yinghua Yu 1, Tan Van Nguyen 1, Hiep Van Tran 2
Affiliations:
1 Đại học Kỹ thuật Liêu Ninh, Trung Quốc
2 Đại học Nghiên cứu Công nghệ Quốc gia (MISiS), Liên bang Nga
- *Corresponding:This email address is being protected from spambots. You need JavaScript enabled to view it.
- Keywords: Le van loi, Xu ping, Yu yinghua, Nguyen van tan, Tran van hiep
- Received: 20th-Sept-2022
- Revised: 15th-Oct-2022
- Accepted: 20th-Nov-2022
- Online: 31st-Dec-2022
Abstract:
In order to study the influence of microstructure and improve the friction pair efficiency of the swash plate axial piston pump, the sliding-swash plate friction pair was selected as the research object. This paper analyzes and evaluates the influence of microstructural geometric parameters on the bearing capacity and friction coefficient under high pressure conditions. Application of the Taguchi method to build experimental matrix, Grey Relation Analysis method (GRA) to analyze the influence of microstructure parameters on the bearing capacity and friction coefficient of the friction pair. Implementation of simulation analysis, compare with the prototype friction pair without microstructure, from which to evaluate the load capacity and coefficient of friction of the sliding-swash plate pair friction pair
1. Taguchi, G. (1987), System of Experimental Design, D. Clausing (Ed), Vols 1-2, UNIPUB/Kraus International Pub-lications, New York.
2. Taguchi, G. and Taguchi, S. (1987), Taguchi Methods: Orthogonal Arrays and Linear Graphs, American Supplier Institute, Dearborn, MI.
3. Murat K. et al. (2011), Friction and wear studies between cylinder liner and pít tông piston ring air using Taguchi design method [J]. Advances in engineering software, 2011,42(3): 59503.
4. Le Van Loi, Xu Ping, Yu Ying Hua (2022), Research Status On Surface Texture In Lubrication And Friction Reduction Of Tribological Systems. Mining Industry Journal. Hanoi, 2022(5):40-48
5. 于英华, 杨帅彬, 曹茂林, 沈佳兴, 阮文新. 滑动轴承表面椭圆偏置类抛物线微织构研究[J/OL]. 表面技术:1-10[2022-01-26].
6. Jonathon K. Schuh，Randy H. Ewoldt (2016), Asymmetric surface textures decrease friction with
Newtonian fluids in full film lubricated sliding contact J], Tribology International 1, 2016,19:490 - 498.
7. 赵亚丽, 张斯琪, 鲁文茜, 陈冲, 魏莉. 基于多指标权重分析和正交设计法优选如意金黄散复方提取工艺[J]. 中国新药杂志, 2021, 30(15):1428-1434.
8. Kasman S. (2013), Multi-response optimization using the Taguchi-based grey relational analysis: a case study for dissimilar friction stir butt welding of AA6082-T6/AA5754-H111. The International Journal of Advanced Manufacturing Technology 68 (1-4):795-804. doi:10.1007/s00170-012-4720-0
9. Singh S. (2012), Optimization of machining characteristics in electric discharge machining of 6061Al/Al2O3p/20P composites by grey relational analysis. The International Journal of Advanced Manufacturing Technology 63 (9-12):1191-1202. doi:10.1007/s00170-012-3984-8
10. Li G-D., Yamaguchi D., Nagai M. (2007), A grey-based rough decisionmaking approach to supplier selection. The International Journal of Advanced Manufacturing Technology 36 (9-10):1032-1040.doi:10.1007/s00170-006-0910-y
11. Abhang LB., Hameedullah M. (2012), Determination of optimum parameters for multi-performance characteristics in turning by using grey relational analysis. The International Journal of Advanced Manufacturing Technology 63 (1-4):13-24. doi:10.1007/s00170-011-3857-6.
12. Younas M., Jaffery SHI., Khan M., Khan MA., Ahmad R., Mubashar A., Ali L. (2019), Multi-objective optimization for sustainable turning Ti6Al4V alloy using grey relational analysis (GRA) based on analytic hierarchy process (AHP). The International Journal of Advanced Manufacturing Technology 105 (1):1175-1188. doi:10.1007/s00170-019-04299-5
Other articles
Mining Industry Journal
No. 226 Le Duan Street, Dong Da District, Hanoi City
Tel:(+84-24) 36649158 Fax: (+84-24) 366159
Email:tccongnghiepmo@gmail.com